Cellwrite Studio operating manual · CWS-OM-001, revision A

The cell

The Cell workspace shows the robots of a cell together. Its sections are Layout, Robot interference and Interlock zones.

Layout

Layout places the robots of the backups open as they stand in the cell. It has four views:

ViewWhat it shows
MapThe cell seen from above.
3DThe robots in place, with their tools, fixtures, tool stands and tracks.
FlowThe parts through the cell: where each robot picks them up, works on them and puts them down.
CyclesWhere each robot's time went in a recording.

How the robots are placed

  • From shared work objects. Robots whose programs hold the same fixed work object are placed together. The list beside the map says how each robot was placed.
  • From a recording. A robot that works on a part another robot holds is placed against it.
  • By hand. Drag a robot on the map to move its group. Turn the mouse wheel while dragging to turn it. Right-click a robot for exact turns.
  • From a photo. Right-click the map and select Place from a photo to place the robots from a picture of the cell's layout screen, a plan or a sketch.

A robot dropped near the fixtures it shares with robots already placed snaps onto them. Hold Alt while dropping to place it freely.

The arrangement is kept for the robots by their serial numbers. It comes back the next time the same robots are opened. Reset layout puts every robot back where its work objects place it.

Tip

To arrange a cell like its twin, right-click the map of the arranged cell and select Copy the arrangement. In the other cell, right-click the map and select Paste the arrangement or Paste the arrangement mirrored.

Moving round the 3D view

ToDo this
Turn the viewDrag.
PanCtrl+drag, or drag with the middle button.
ZoomTurn the mouse wheel.
See the whole cellDouble-click an empty place.
Full screenF11.

Robot interference

Robot interference finds where two robots' programs can collide.

Run analysis

  1. Select Cell > Robot interference.
  2. Select the two robots.
  3. Select Run analysis. Every move of one robot is checked against every move of the other.
  4. The results list each place the robots come closer than the margin, with the routines, lines and distance. Select a result to see the two robots there in 3D.
  5. To file the result, select Save report…. The report is a PDF or a web page with the two robots, their programs and tools, the margin and every clash in the list. A check with no clashes gives a report that says so.

Play programs

Play programs plays the two robots' programs side by side, in 3D, with each robot's code beside the view.

  • Each robot has a bar along the bottom. Both bars use one scale of seconds, shown on the ruler under them, so the same moment is at the same place on both. A shorter program's bar ends where its program does. Drag a robot's bar to move that robot alone. The other robot stays where it is.
  • Each bar is coloured by how close its robot would come to the other robot where that robot stands now: red where they meet, amber when close, green when well apart.
  • The number at the top is the closest distance between the two robots now.
  • PP to cursor moves a robot to the move at the cursor in its code panel. Show pointer brings its code panel back to the line it is on.
  • Show paths draws each robot's tool path in the same colours.
  • The options under the robots choose what the 3D view shows: Tool envelope (each tool's SafeMove shapes or box), Tool models, Collision spheres and SafeMove zones.
  • Right-click in a code panel for PP to line, Show pointer, Copy and Select all.
KeysCommand
SpacePlay or pause
HomeBoth robots to the start
Left / RightBoth robots back or on 1 s (Shift: 0.1 s)
Page Up / Page DownPrevious or next clash

Note

The robots are measured with their collision models: the arm, the tool and the payload as spheres and boxes round them. The analysis says where to look. It does not prove that a cell is free of collisions.

Interlock zones

Interlock zones reads the zones the robots ask for and release before they enter a shared space, and checks that two robots never hold the same zone at once.

  • Scan again reads the programs again.
  • Export writes the zones and who holds them where to Excel.
  • Settings sets the names of the zone signals, when they do not follow the program's usual pattern.

SafeMove zones

The SafeMove zones in the backup can be shown in the 3D views. A zone the robot enters is drawn in red. The zones are checked by Cellwrite Studio, not by SafeMove.